Betekenis van:
dead load

Voorbeeldzinnen

1. Make(s):4.3.2.4.2. Type(s):4.3.2.4.3. Speed at which cut-off starts under full load (2): … r/min4.3.2.4.4. Maximum no-load speed (2): … r/min4.3.2.4.5. Idling speed (2): … r/min4.3.3. Cold-start system4.3.3.1. Make(s):4.3.3.2. Type(s):4.3.3.3. Description:4.4. Valve timing4.4.1. Maximum lift and opening and closing angles in relation to top dead centre or equivalent data:4.4.2. Reference clearances and/or setting ranges (1):4.4.3. Variable valve timing system (if applicable and where intake and/or exhaust)4.4.3.1. Type: continuous or on/off4.4.3.2. Cam phase shift angle:4.5. Porting configuration4.5.1.
2. Make(s):4.3.2.4.2. Type(s):4.3.2.4.3. Speed at which cut-off starts under full load (2): … r/min4.3.2.4.4. Maximum no-load speed (2): … r/min4.3.2.4.5. Idling speed (2): … r/min4.3.3. Cold-start system4.3.3.1. Make(s):4.3.3.2. Type(s):4.3.3.3. Description:4.4. Valve timing4.4.1. Maximum lift and opening and closing angles in relation to top dead centre or equivalent data:4.4.2. Reference clearances and/or setting ranges (1):4.4.3. Variable valve timing system (if applicable and where intake and/or exhaust)4.4.3.1. Type: continuous or on/off4.4.3.2. Cam phase shift angle:4.5. Porting configuration4.5.1. Position, size and number:4.6. Electronic command functionsIf the engine features electronically controlled functions, information concerning their performance must be provided including:4.6.1. Make:4.6.2. Type:4.6.3. Part number:4.6.4. Location of engine electronic control unit:4.6.4.1. What does it sense:4.6.4.2. What does it control: ’;
3. Fuel feed3.2.3.1. Feed pumpPressure (2) or characteristic diagram: kPa3.2.3.2. Injection system3.2.3.2.1. Pump3.2.3.2.1.1. Make(s):3.2.3.2.1.2. Type(s):3.2.3.2.1.3. Delivery: mm3 (2) per stroke or cycle at pump speed of: r/min (rated) and r/min (maximum torque), respectively, or characteristic diagramState which method is used: on engine/on pump bench (1)3.2.3.2.1.4. Injection advance3.2.3.2.1.4.1. Injection advance curve (2):3.2.3.2.1.4.2. Timing (2):3.2.3.2.2. Injection piping3.2.3.2.2.1. Length: mm3.2.3.2.2.2. Internal diameter: mm3.2.3.2.3. Injector(s)3.2.3.2.3.1. Make(s):3.2.3.2.3.2. Type(s):3.2.3.2.3.3. Opening pressure (2) or characteristic diagram:3.2.3.2.4. Governor3.2.3.2.4.1. Make(s):3.2.3.2.4.2. Type(s):3.2.3.2.4.3. Speed at which cut-off starts under full load (2): r/min3.2.3.2.4.4. Maximum no-load speed (2): r/min3.2.3.2.4.5. Idling speed (2): r/min3.2.3.3Cold-start system3.2.3.3.1. Make(s):3.2.3.3.2. Type(s):3.2.3.3.3. Description:3.2.4. Valve timing3.2.4.1. Maximum lift and angles of opening and closing in relation to top dead centre or equivalent data:3.2.4.2. Reference clearances and/or setting ranges (1)